Showing results: 106 - 120 of 152 items found.
-
cPCI4IP -
Dynamic Engineering
The cPCI [CompactPCI] compatible cPCI4IP design adds 4 Industrypack compatible slots to your cPCI host. The cPCI4IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI4IP is a 6U 4HP cPCI design with 4 IP slots.
-
cPCIBPMC -
Dynamic Engineering
The cPCIBPMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCIBPMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
cPCI2IP -
Dynamic Engineering
The cPCI [Compact PCI] compatible cPCI2IP design adds 2 Industrypack compatible slots to your cPCI host. The cPCI2IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI2IP is a 3U 4HP cPCI design with 2 IP slots.
-
APC-PMC -
Acromag, Inc.
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard PCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the PCI card slot edge connector.
-
PC2 -
SCSI Toolbox, LLC
The PC2 software from SCSI Toolbox, LLC brings a new level of parallel SCSI protocol control to your test environment. Designed in cooperation with LSI Logic to work with their Fusion-MPT Message Passing Interface technology, PC2 allows all negotiated parameters to be displayed or set for all devices connected to any SCSI Host Bus Adapter based on the LSI53C1030 chip set. PC2 also provides the means to generate hardware SCSI bus resets.
-
SKU-055-0X -
Amfeltec Corp.
The Flexible MiniPCI Express Riser (Riser) was designed to extend the MiniPCI Express bus. The Riser includes a MiniPCI Express adapter board (downstream), MiniPCI Express host board and a 12” PCI Express flat cable.The MiniPCI Express host board connects to the motherboard MiniPCI Express connector.
-
APCI-7300-3 -
TEAM SOLUTIONS, INC.
*PCI interface to the 32-bit data bus. *Asynchronous communication adapter, 1-port serial interface*1 socket for SI modules*Modular structure through SI modules*Configurable as: RS232, RS422, RS485, with or without isolation, or 20 mA Current Loop (active, passive) with isolation*Addressing through software
-
PMC-MC-X2 -
Dynamic Engineering
The PMC-MC-X2 adapter / carrier converter card provides the ability to install up to 2 (two) PMC cards into a small enclosure. The PMC-MC-X2 has one PMC card slot mounted front and rear to create a compact arrangement with 2 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
PMC-MC-X4 -
Dynamic Engineering
The PMC-MC-X4 adapter / carrier converter card provides the ability to install up to 4 (four) PMC cards into a small enclosure. The PMC-MC-X4 has two PMC card slots mounted front and rear to create a compact arrangement with 4 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
60-982-001 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
60-982-002 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
PCI2cPCI -
Dynamic Engineering
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
PCI2cPCI-32 -
Dynamic Engineering
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
PCI3IP -
Dynamic Engineering
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solutions.
-
PCChost 1420 -
Sycard Technology
Based on Texas Instruments' PCI1420 CardBus host adapter chip, the PCChost 1420 PCI-to-CardBus bridge provides the engineer with a platform to evaluate a high performance ACPI compliant CardBus bridge device. Contained on a single Peripheral Component Interconnect (PCI) bus card, the PCChost 1420 is compatible with a wide variety of PC and non-PC PCI hosts.
